A cracked excavator bucket. A dead trailer hitch. A dump truck bed split down the seam. Every hour that equipment sits idle is an hour your crew is on the clock doing nothing — and hauling it to a shop just adds another day to the wait. Proud Mobile Welding repairs heavy equipment and machinery on-site, wherever it sits — construction gear, agricultural implements, and industrial machinery. We bring everything we need to the job. No towing, no shop appointment, no losing a day of work you don't have to lose.
✓ On-Site Equipment Repair — No Towing ✓ Owner-Operated — 20 Years Experience ✓ Certified Fully Self-Powered Rigs ✓ No Hidden Fees
Here is what nobody tells you when your equipment breaks down in Austin.
A crack doesn't happen for no reason. It happens because a component was undersized for the load it was carrying, a weld was never done right the first time, or stress kept concentrating on the same point until something gave.
A quick weld over the crack without addressing why it happened will fail again — usually sooner than you'd expect, and usually at the worst possible time.
The metal fatigues. The stress finds the same weak point. The equipment goes down again.
And eventually you're paying for the same repair twice — plus the downtime it cost you the second time around.
Diagnosing why something failed and repairing it correctly are two separate skills that require two separate levels of experience.
Most repair outfits do the first part and skip the second.
Proud Mobile Welding does not.
We assess every failure on-site — why it happened, not just what broke. If a component failed because it wasn't built for the load it was carrying, we reinforce or replace it with the correct spec, not just patch over the crack.
The equipment is then repaired and back in service the same day whenever the job allows, on-site, with no towing and no shop appointment.
The result is a repair that holds up, not one you'll be paying for again in six months.
Every repair Proud Mobile Welding handles is diagnosed and welded on-site, wherever the equipment sits. Here are the most common equipment failures we're called out for across Greater Austin.
What We Build
A bucket that's cracked at the seam or worn through at the cutting edge doesn't just slow down a job — it stops it. Cracks start small and spread fast under repeated impact, especially in rocky or caliche-heavy Central Texas soil. We re-weld cracked seams, rebuild worn edges, and reinforce high-stress points on-site. Best for: Excavators, loaders, and skid steers with visible cracks, worn cutting edges, or bent bucket walls.
A dump bed that's cracked along the floor or a trailer frame that's bent from overload doesn't get fixed by ignoring it — the crack spreads with every load cycle until the bed fails completely. We repair cracked beds, reinforce worn floor plates, and straighten or replace damaged trailer frame sections on-site. Best for: Dump trucks and trailers with cracked beds, worn liners, or frame damage from heavy or uneven loads.
A sheared hitch pin or a cracked PTO mount takes a piece of equipment out of service at the worst possible time — usually mid-season, mid-field. We repair and reinforce hitch assemblies, drawbars, and PTO components on-site, wherever the equipment sits. Best for: Tractors, implements, and trailers with damaged hitches, worn drawbars, or PTO components that won't engage properly.
Skid steers take constant stress at the attachment mounting points — quick-attach plates crack, mounting pins wear oversized, and hydraulic brackets bend under load. We repair mounting plates, rebuild worn pin bores, and reinforce attachment points on-site. Best for: Skid steers and attachments with worn quick-attach systems, cracked mounting plates, or bent hydraulic brackets.
A crack in a boom, a bent outrigger, or a failed weld on lift equipment isn't something to patch and hope holds — the safety margin on lifting equipment doesn't allow for a guess. We assess structural damage on-site and repair it to the load rating the component actually needs to carry. Best for: Cranes, boom lifts, and other lifting equipment with visible cracks, bent structural members, or failed welds.
A proper equipment repair has two distinct steps — diagnosing why it failed, and welding it to hold. Here is exactly how Proud Mobile Welding handles both.
This is what we assess first. Where the crack started, why the component failed under the load it was carrying, and how the connection points, material thickness, and stress distribution were originally built. Getting this part right is the foundation of everything else. A repair based on an accurate diagnosis will hold reliably for years. A repair that just covers the visible damage without understanding the cause will begin failing again — and stressing the same weak point — within months.
This is where we weld. Proper joint preparation, correct penetration, and reinforcement matched to the actual working load the component carries — not a surface pass that looks fine until it's back under stress. Equipment repair requires understanding fatigue points and load paths that goes beyond a quick patch job. By diagnosing before we weld, we make sure your equipment is repaired correctly the first time — and built to carry the load it's actually going to see.
When a repair shop just welds over visible damage without understanding why it happened, the temptation is to take the fast path and move to the next job. Proud Mobile Welding does not have that incentive. We diagnose the actual failure first, regardless of how much longer it takes upfront — because a repair that fails again in six months costs everyone more than doing it right the first time.
The cracked bucket that a dealer says isn't worth their trip. The bent hitch that doesn't justify a full equipment replacement. The failure that's costing you money by the hour while a shop tells you to wait three weeks. These are exactly the jobs Proud Mobile Welding takes. If it's structural, made of steel, and broken — call us.
Cost depends on the severity of the damage and the type of equipment — a cracked bracket costs less than a major structural failure on a bucket or frame. We provide an itemized estimate on-site before any work begins, so there are no surprises
Excavators, loaders, skid steers, dump trucks, trailers, tractors, agricultural implements, and lifting equipment like booms and cranes. If it's steel and it's structural, we can likely repair it — call and describe the damage if you're not sure.
Yes. Our mobile setup is fully self-powered — no generator rental, no extension cords, no need to access your property or job site's electrical panel.
Yes. We assess it on-site the same way we would our own work and repair it properly, regardless of who originally built or repaired it
Most on-site repairs are completed the same day. More extensive structural work may take longer, and we'll give you a realistic timeline after the on-site assessment — before any work begins.
Not if the failure is properly diagnosed first. We identify why the original failure happened — undersized components, a stress point, a bad original weld — and repair to the correct spec, so the same failure doesn't repeat.
Yes. We work with construction crews, general contractors, agricultural operations, and equipment owners across Central Texas — wherever the equipment breaks down.
Both. If a piece of equipment goes down mid-job and you need it back in service fast, we dispatch the same day whenever possible. Scheduled repairs get an estimate first, same as any other job
Usually a previous repair patched the visible crack without addressing why it happened — an undersized component, a stress point that was never reinforced, or a weld that wasn't done with proper penetration. We diagnose the actual cause before we weld, so the fix holds instead of failing again in the same place.
Your equipment deserves a repair that actually holds — not a patch that fails again in six months. Whether you’re in Westlake Hills, Lakeway, Round Rock, Cedar Park, or anywhere across Greater Austin — call or text us directly. We’ll talk through what broke, what it’ll take to fix it, and how fast we can get there. No sales pitch. Just a straight answer.
© 2026 Proud Mobile Welding ALL Rights Reserved